木片筛余物高得率半化学法清洁制浆技术研究

以太阳纸业备料车间木片筛选碎料（筛余物）为原料，对其烧碱法半化学制浆的实验室工艺和生产试验进行了研究。结果表明，筛余物采用半化学法制浆可获得较高得率和环压强度的纸浆，且用碱量对纸浆性能有显著影响。相对8%NaOH （相对于绝干原料）化学预处理，采用14%NaOH化学预处理结合两段浆浓22%的高浓磨浆工艺，所制半化学浆抄造浆张的裂断长和环压指数分别达2.89 km和9.76 N·m/g，是前者的1.9倍和1.2倍，而且优于现用国内OCC废纸浆抄造浆张；生产试验得到的浆张性能指标与实验室相吻合，其中紧度和环压强度分别达到GB/T 13023—2008瓦楞芯（原）纸AA级和A级优等品要求。     

基于归一化水体指数及其阈值自适应算法的水体遥感反演效果分析

归一化水体指数（NDWI）是水体遥感反演的一种重要指标，其阈值及修正直接影响反演结果的精度。基于Landsat-8与GF-1光学多光谱影像，使用归一化水体指数法阈值0（TH₀）、最大类间方差法（OTSU）自适应阈值（TH_otsu）与均值漂移聚类算法（Mean-Shift）自适应阈值（TH_MS）分别对典型正常水体、云雾覆盖水体、富营养化水体、高含泥沙水体进行水体遥感提取与效果分析，结果表明：正常水体以TH₀为阈值提取精度最高，THMS提取精度次之，TH_otsu提取精度最差；而云雾覆盖水体、富营养化水体以及含泥沙水体使用THMS提取精度最高，尤其少量云雾覆盖下的水体，TH_MS具有更明显的优势，TH₀提取精度次之，TH_otsu提取精度最差；对于不同的阈值，Land?sat-8比GF-1总体表现出更高的水体提取精度。Mean-Shift算法应用于NDWI阈值修正与水体遥感反演具有快速、水质适应性强、效果稳定的优势，对尤其是复杂条件下的水体信息遥感反演具有较好的提取效果。     

CDBN‑IKELM的轴承变工况故障诊断方法

针对现有方法在轴承变工况方面存在的诊断精度低、人工提取特征不充分等问题，提出了基于卷积深度置信网络（convolutional deep belief network，简称CDBN）与改进核极限学习机 （improved Kernel?based extreme learning machine，简称IKELM）的滚动轴承故障智能识别方法。首先，由卷积深度置信网络对原始信号内的故障特征进行深层自适应提取；其次，利用等距特征映射对提取的多维特征进行降维，去除冗余特征信息；然后，采用改进的核极限学习机对特征进行分类，使用粒子群（particle swarm optimization， 简称PSO）对模型重要参数进行优化，实现滚动轴承变工况下的故障识别；最后，将所提方法应用于不同工况下多种轴承故障的诊断。实验结果表明，该方法能够智能有效地识别变工况的轴承故障，诊断结果优于已有的智能故障诊断方法。     

Effects of Solution Treatment Temperatures on Microstructure and Mechanical Properties of TIG–MIG Hybrid Arc Additive Manufactured 5356 Aluminum Alloy

A novel additive manufacturing method with TIG–MIG hybrid heat source was applied for fabricating 5356 aluminum alloy component. In this paper the microstructure evolution, mechanical properties and fracture morphologies of both as-deposited and heat-treated component were investigated, and how these were affected by different heat-treated temperature. The as-deposited microstructure showed dominant equiaxed grains with second phase, and the size of them is coarse in the bottom region, medium in the middle region and fine in the top region owing to different thermal cycling conditions. Compared with as-deposited microstructure, the size of grain becomes large and second phases gradually dissolve in the matrix as heat-treated temperature increase. Different microstructures determine the mechanical properties of component. Results show that average ultimate tensile strength enhances from 226 to 270 MPa and average microhardness increases from 64.2 to 75.3 HV0.1 but ductility decreases from 33 to 6.5% with heat-treated temperature increasing. For all components, the tensile properties are almost the same in the vertical direction (Z) and horizontal direction (Y) due to equiaxed grains, which exhibits isotropy, and the mechanisms of these are analyzed in detailed. In general, the results demonstrate that hybrid arc heat source has the potential to fabricate aluminum alloy component.     

微波水热辅助沉淀法制备氧化铝/碳化硅复合粉体

用微波水热辅助沉淀法制得氧化铝前驱体/碳化硅复合粉体,用XRD、SEM、TG-DSC对粉体进行了表征.研究表明:经过微波水热后,氧化铝的前驱体转变为AlO(OH),随着微波水热时间延长,AlO(OH)的结晶程度越来越高.pH值为7时,煅烧后的Al2 O3/SiC复合粉体的包覆效果最佳.     

A comparative study on pyrolysis reactivity and gas release characteristics of biomass and coal using TG-MS analysis

Pyrolysis reactivity and gas release characteristics of biomass and coals were comparatively investigated using TG-MS. In addition, chemical compositions and structures of tested samples were determined to correlate pyrolysis gas release characteristic. It was found that pyrolysis reactivity and gaseous product release were hardly varied with pyrolysis heating rate. Furthermore, pyrolysis rates of two biomass samples were greater than those of coals, which were mainly attributed to the chemical compositions and the gaseous product evolution process. The result also showed that gaseous product release during pyrolysis process was related to the presence of different functional groups in samples.     

基于Radon-CPF-Fourier变换的机动目标ISAR成像

由于机动目标的逆合成孔径雷达（Inverse Synthetic Aperture Radar，ISAR）成像中存在多普勒扩散现象，易导致成像分辨率降低。针对此问题，在多分量三次相位信号（Cubic Phase Signal,CPS）模型基础上，提出一种基于Radon-CPF-Fourier变换（Radon-Cubic Phase Function-Fourier Transform,RCFT）的机动目标ISAR成像方法。RCFT可实现CPF中自项能量的相干积累，减轻多普勒扩散带来的影响。与现有的基于时频分析和参数估计的ISAR成像算法相比，RCFT的主副比性能提升了至少2 dB，在时频分辨率无损失时具备更好的自项能量积累能力，可获得更高质量的成像结果。仿真验证了所提方法的有效性。     

Improving Properties of Poly(vinylidene fluoride) by Adding Expanded Graphite without Surface Modification via Water‐Assisted Mixing Extrusion

Expanded graphite (EG) is introduced into poly(vinylidene fluoride) (PVDF) by melt mixing extrusion with water injection. The results demonstrate that the unfunctionalized EG in composite prepared with water injection exbibits better dispersion than that in the one prepared without water injection due to the promoting role of water during extrusion. Thus, the PVDF/EG composite with loading of 4 wt% prepared by water‐assisted mixing extrusion (WAME) exhibits electrical conductivity of about three orders of magnitude higher than the neat PVDF and one order of magnitude higher than the one prepared without water injection. Comparing to the neat PVDF, the thermal conductivity of the composites prepared with and without water injection is increased by 101.5% and 75.0%, respectively. The introduced EG leads to increased Young’s modulus and tensile strength especially for the composite prepared by WAME. The present work indicates that WAME can promote the dispersion of EG in PVDF matrix without any extra functionalization.     

碱铝硅酸盐玻璃化学强化关键影响因素概述

化学强化是一种玻璃机械强度增强方法,适用于异型、超薄、高碱、高膨胀玻璃增强,因新型超薄显示产品的屏幕保护玻璃发展需要,化学强化技术重新在碱铝硅酸盐玻璃品种掀起研究热潮。本文对化学强化本质及铝硅酸盐玻璃在屏幕保护玻璃应用进行了回顾,基于玻璃化学强化的高CS、DOL和低CT诉求,归纳总结了关键影响因素,第1,碱铝硅酸盐玻璃的成分及结构是基础,氧化铝有利玻璃网络孔隙增大创造交换通道,氧化钠或氧化锂是离子交换关键物质;第2,对于玻璃组成和结构设计,要求玻璃网络键合度R=O/Si或O/(Si+Al)满足2.15~2.40,碱金属氧化物质量分数大于13%且膨胀系数大于6×10^-6/℃;第3,在化学强化工艺方面,化学强化温度决定离子扩散系数,化学强化时间决定DOL,一步法仅能获得相对较大的CS,而DOL不很理想,只有两种离子参与交换的二步法才有利于CS和DOL同步提高。